Panasonic H-X025E Инструкция по применению

Категория
Объективы для камеры
Тип
Инструкция по применению

Это руководство также подходит для

Before use, please read these instructions completely.
E
VQT3N28
Operating Instructions
INTERCHANGEABLE LENS FOR DIGITAL CAMERA
Model No. H-X025
until
2011/7/19
VQT3N28_E.book 1 ページ 2011年5月26日 木曜日 午前9時34分
2
VQT3N28
Contents
Information for Your Safety..................................... 2
Precautions........................................................... 5
Supplied Accessories ............................................. 6
Attaching/Detaching the Lens................................. 6
Names and Functions of Components ................... 8
Cautions for Use..................................................... 9
Troubleshooting .................................................. 10
Specifications........................................................ 11
Information for Your Safety
Keep the unit as far away as possible from
electromagnetic equipment (such as microwave
ovens, TVs, video games, radio transmitters,
high-voltage lines etc.).
Do not use the camera near cell phones because
doing so may result in noise adversely affecting
the pictures and sound.
If the camera is adversely affected by
electromagnetic equipment and stops functioning
properly, turn the camera off and remove the
battery and/or the connected AC adaptor. Then
reinsert the battery and/or reconnect the AC
adaptor and turn the camera on.
VQT3N28_E.book 2 ページ 2011年5月26日 木曜日 午前9時34分
3
VQT3N28
The lens can be used with a digital camera
compatible with the lens mount standard for the
“Micro Four Thirds
TM
System”.
It cannot be mounted on the Four Thirds
TM
mount
specification camera.
The digital camera illustrations in these operating
instructions show DMC-G3 as an example.
The appearance and specifications of products
described in this manual may differ from the actual
products you have purchased due to later
enhancements.
Micro Four Thirds
TM
and Micro Four Thirds Logo
marks are trademarks or registered trademarks of
Olympus Imaging Corporation, in Japan, the
United States, the European Union and other
countries.
Four Thirds
TM
and Four Thirds Logo marks are
trademarks or registered trademarks of Olympus
Imaging Corporation, in Japan, the United States,
the European Union and other countries.
G MICRO SYSTEM is a lens exchange type
digital camera system of LUMIX based on a Micro
Four Thirds System standard.
LEICA is a registered trademark of Leica
Microsystems IR GmbH.
SUMMILUX
is a
registered trademark of Leica Camera AG. The
LEICA DG lenses are manufactured using
measurement instruments and quality assurance
systems that have been certified by Leica Camera
AG based on the company’s quality standards.
Other names of systems and products mentioned
in these instructions are usually the registered
trademarks or trademarks of the manufacturers
who developed the system or product concerned.
ENGLISH
VQT3N28_E.book 3 ページ 2011年5月26日 木曜日 午前9時34分
4
VQT3N28
-If you see this symbol-
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private
households)
This symbol on the products and/or accompanying documents means that used
electrical and electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to
designated collection points, where they will be accepted on a free of charge basis.
Alternatively, in some countries you may be able to return your products to your local
retailer upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent
any potential negative effects on human health and the environment which could
otherwise arise from inappropriate waste handling. Please contact your local authority
for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct
method of disposal.
VQT3N28_E.book 4 ページ 2011年5月26日 木曜日 午前9時34分
5
VQT3N28
Lens Care
Sand and dust can damage the lens. Make
sure that no sand or dust gets inside the lens
or the terminals when using the lens on a
beach, etc.
This lens is not waterproof. If drops of water
get onto the lens, wipe the lens with a dry
cloth.
Do not press the lens with excessive force.
When there is dirt (water, oil, and fingerprints, etc.)
on the surface of the lens, the picture may be
affected. Lightly wipe the surface of the lens with a
soft, dry cloth before and after taking pictures.
Do not place the lens mount facing downwards.
Do not allow the lens contact points 1 to become
dirty.
About Condensation (Fogging of the
Lens)
Condensation occurs when there are differences
in temperature and humidity as described below.
Condensation can cause the lens to become dirty
and lead to mold and malfunctioning, so exercise
caution in the following situations:
– When the camera is brought indoors from outside
during cold weather
When the camera is brought into an air-
conditioned car
When cold air from an air conditioner is directly
blown onto the lens
In humid places
Put the camera into a plastic bag to allow it to
acclimatize to the surrounding temperature in
order to prevent condensation. If condensation
occurs, turn the power off and leave it for about
two hours. Once the camera acclimatizes to the
surrounding temperature the condensation will go
away naturally.
Precautions
VQT3N28_E.book 5 ページ 2011年6月14日 火曜日 午前11時49
6
VQT3N28
Supplied Accessories
[Inspection to be performed when you unpack
the unit]
When removing the unit from its packing box, check
that the main unit and the supplied accessories are
there and also check their external appearance and
functions to verify that they have not sustained any
damage during distribution and transportation.
If you discover any trouble, contact your vendor
before using the product.
Product numbers correct as of July 2011. These
may be subject to change.
1 Lens Storage Bag
2 Lens Hood
3 Lens Cap
4 Lens Rear Cap
(The lens rear cap and lens cap are attached to
the interchangeable lens at the time of purchase.)
Attaching/Detaching the Lens
Refer also to the camera’s operating instructions
for attaching and detaching the lens.
Attaching the Lens
Check that the camera is turned off.
1 Turn the lens rear
cap to detach it.
A: Lens Rear Cap
2 Align the lens fitting
marks B (red marks) on
the camera body and the
lens and then rotate the
lens in the direction of
the arrow until it clicks.
Do not press the lens release
button C when you attach a lens.
Do not try to attach the lens when holding it at an
angle to the camera body as the lens mount may
get scratched.
Check that the lens is attached correctly.
VFC4456 VYC1063 VYF3284
123
VFC4605
4
VQT3N28_E.book 6 ページ 2011年5月26日 木曜日 午前9時34分
7
VQT3N28
Detaching the Lens
Check that the camera is turned off.
While pressing on the
lens release button D,
rotate the lens toward the
arrow until it stops and
then remove.
Attach the lens rear cap so
that the lens contact point
does not get scratched.
Attach the body cap to the camera so no dirt or
dust will get inside the main unit.
Attaching and Detaching the Lens Cap
Pinch the lens cap as shown in the figure
to attach or detach.
• Be careful not to lose
the lens cap.
Attaching the Lens Hood
(Supplied Accessory)
Insert the lens hood into the lens with the
short sides at the top and bottom, and
turn in the direction of the arrow until it
stops.
E: Fit to the mark
When taking pictures with the flash with the lens
hood attached, the lower portion of the screen
may turn dark (vignetting effect) and the control
of the flash may be disabled because the photo
flash may be obscured by the lens hood. We
recommend detaching the lens hood.
When using the AF assist lamp in the dark,
detach the lens hood.
VQT3N28_ENG.fm 7 ページ 2011年6月28日 火曜日 午後2時56分
8
VQT3N28
Attaching Filters
Vignetting may occur if using 2 or more
MC protectors (optional: DMW-LMC46),
PL filters (optional: DMW-LPL46) or ND filters
(optional: DMW-LND46), or if using thick
protectors and/or filters.
The filter may become impossible to remove if
excessively tightened, so please refrain from
tightening it too strongly.
It is possible to attach the lens cap with the filter
already attached.
You cannot attach a conversion lens or adaptor to
this lens. A filter may be used, but attaching any
other element may cause damage to the lens.
Names and Functions of
Components
1 Lens surface
2 Focus ring
Rotate to focus when taking pictures with
manual focus.
3 Contact points
4 Lens fitting mark
4
21
3
VQT3N28_E.book 8 ページ 2011年6月14日 火曜日 午前11時49
9
VQT3N28
Note
Change in the image by the focus operation may
be more visible depending on the recording
condition when the AF operates during the motion
picture recording. It is recommended to fix the
focus by setting the camera to manual focus (MF),
etc., when the change of image is disturbing you.
Cautions for Use
Take care not to drop or knock the lens. Also
take care not to put a lot of pressure on the lens.
Take care not to drop the bag that you inserted the
lens in as it may strongly shock the lens. The
camera may stop operating normally and pictures
may no longer be recorded. Also, the lens may be
damaged.
When using pesticides and other volatile
substances around the camera make sure that
they do not get onto the lens.
If such substances get onto the lens they can
damage the exterior case or cause the paint to
peel.
Do not carry the unit when it is still attached to
the camera body.
Under no circumstances should the unit be stored
in any of the following locations since doing so
may cause problems in operation or
malfunctioning.
In direct sunlight or on a beach in summer
VQT3N28_E.book 9 ページ 2011年5月26日 木曜日 午前9時34分
10
VQT3N28
In locations with high temperatures and humidity
levels or where the changes in temperature and
humidity are acute
In locations with high concentrations of sand,
dust or dirt
Where there is fire
Near heaters, air conditioners or humidifiers
Where water may make the unit wet
Where there is vibration
Inside a vehicle
Refer also to the operating instructions of the
digital camera.
When the unit is not going to be used for a
prolonged period, we recommend storing with a
desiccant (silica gel). Failure to do so may result in
performance failure caused by mold, etc. It is
recommended that you check the unit’s operation
prior to use.
Do not leave the lens in contact with rubber or
plastic products for extended periods of time.
Do not touch the lens contact point. Doing so can
cause failure of the unit.
Do not disassemble or alter the unit.
Do not use benzine, thinner, alcohol or other
similar cleaning agents to clean the lens glass or
exterior cabinet.
Using solvents can damage the lens or cause the
paint to peel.
Wipe off any dust or fingerprints with a soft, dry
cloth.
Use a dry dust cloth to remove dirt and dust on
the focus ring.
Do not use a household detergent or a chemically
treated cloth.
A sound is heard when the camera is turned on
or off.
A sound is heard from the lens when taking a
picture of a bright subject such as when
outdoors.
This is the sound of lens or aperture movement
and is not a malfunction.
Troubleshooting
VQT3N28_E.book 10 ページ 2011年5月26日 木曜日 午前9時34分
11
VQT3N28
Specifications
INTERCHANGEABLE LENS FOR DIGITAL CAMERA
“LEICA DG SUMMILUX 25 mm/F1.4 ASPH.”
Focal length f=25 mm
(35 mm film camera equivalent: 50 mm)
Aperture type 7 diaphragm blades/circular aperture diaphragm
Aperture range F1.4
Minimum aperture value F16
Lens construction 9 elements in 7 groups (2 aspherical lenses)
In focus distance 0.3 m
to (from the focus distance reference line)
Maximum image magnification 0.11k (35 mm film camera equivalent: 0.22k)
Optical image stabilizer Not available
Mount “Micro Four Thirds Mount”
Angle of view 47x
Filter diameter 46 mm
Max. diameter Approx. 63 mm
Overall length Approx. 54.5 mm
(from the tip of the lens to the base side of the lens mount)
Mass Approx. 200 g
VQT3N28_E.book 11 ページ 2011年5月26日 木曜日 午前9時34分
12
VQT3N28
Inhalt
Informationen für Ihre Sicherheit.................................12
Vermeidung von Störungen ......................................15
Beiliegendes Zubehör.................................................16
Objektiv ansetzen/abnehmen .....................................16
Bezeichnungen und Funktionen der
einzelnen Kamerateile ................................................18
Vorsichtsmaßnahmen.................................................19
Fehlerbehebung........................................................20
Spezifikationen ...........................................................21
Informationen für Ihre
Sicherheit
Halten Sie das Gerät so weit wie möglich von
Geräten und Einrichtungen fern, die
elektromagnetische Felder erzeugen (wie
Mikrowellengeräte, Fernsehgeräte,
Videospielgeräte, Funksender,
Hochspannungsleitungen usw.).
Verwenden Sie die Kamera nicht in der Nähe von
Mobiltelefonen. Es könnten sonst Bild- und
Tonstörungen auftreten.
Wenn die Kamera durch elektromagnetische
Felder anderer Geräte gestört wird und
Fehlfunktionen auftreten, schalten Sie die Kamera
aus. Nehmen Sie den Akku heraus und/oder
trennen Sie das Netzteil ab. Setzen Sie den Akku
dann wieder ein und/oder stecken Sie das Netzteil
wieder ein und schalten Sie die Kamera ein.
VQT3N28_E.book 12 ページ 2011年6月14日 火曜日 午前11時49
13
VQT3N28
Das Objektiv kann mit Digitalkameras verwendet
werden, deren Objektivfassung mit dem “Micro Four
Thirds™ System”-Standard kompatibel ist.
Objektive dieser Ausführung lassen sich nicht auf
Kameras mit Four-Thirds™-Bajonett aufsetzen.
Die Erläuterungen zur Digitalkamera in dieser
Bedienungsanleitung beziehen sich als ein
Beispiel auf DMC-G3.
Ausstattung und technische Daten der von Ihnen
erworbenen Produkte können aufgrund
technischer Weiterentwicklungen von der
Ausstattung und den technischen Daten der in
diesem Handbuch beschriebenen Produkte
abweichen.
Micro Four Thirds™ und die für Micro Four Thirds
verwendeten Logos sind Markenzeichen oder
eingetragene Markenzeichen der Olympus
Imaging Corporation in Japan, den USA, der EU
und anderen Ländern.
Four Thirds™ und die für Four Thirds
verwendeten Logos sind Markenzeichen oder
eingetragene Markenzeichen der Olympus
Imaging Corporation in Japan, den USA, der EU
und anderen Ländern.
Das G MICRO SYSTEM ist ein
Digitalkamerasystem aus der LUMIX-Reihe mit
Wechselobjektiven auf Grundlage des Micro-Four-
Thirds-Standards.
LEICA ist ein eingetragenes Markenzeichen der
Leica Microsystems IR GmbH.
SUMMILUX
ist ein
eingetragenes Markenzeichen der Leica Camera
AG. Die Herstellung der LEICA DG-Objektive
erfolgt unter Verwendung von Messinstrumenten
und Qualitätssicherungssystemen, die von der
Leica Camera AG auf Grundlage der
Qualitätsstandards des Unternehmens zertifiziert
wurden.
Andere Namen von Systemen oder Produkten
welche in dieser Bedienungsanleitung genannt
werden, sind normalerweise Warenzeichen oder
eingetragene Warenzeichen der Hersteller dieser
Produkte oder Systeme.
DEUTSCH
VQT3N28_E.book 13 ページ 2011年5月26日 木曜日 午前9時34分
14
VQT3N28
-Bedeutung des nachstehend abgebildeten Symbols-
Benutzerinformationen zur Entsorgung von elektrischen und elektronischen Geräten (private
Haushalte)
Entsprechend der grundlegenden Firmengrundsätzen der Panasonic-Gruppe wurde
ihr Produkt aus hochwertigen Materialien und Komponenten entwickelt und
hergestellt, die recycelbar und wieder verwendbar sind.
Dieses Symbol auf Produkten und/oder begleitenden Dokumenten bedeutet, dass
elektrische und elektronische Produkte am Ende ihrer Lebensdauer vom Hausmüll
getrennt entsorgt werden müssen.
Bringen Sie bitte diese Produkte für die Behandlung, Rohstoffrückgewinnung und
Recycling zu den eingerichteten kommunalen Sammelstellen bzw.
Wertstoffsammelhöfen, die diese Geräte kostenlos entgegennehmen.
Die ordnungsgemäße Entsorgung dieses Produkts dient dem Umweltschutz und
verhindert mögliche schädliche Auswirkungen auf Mensch und Umwelt, die sich aus
einer unsachgemäßen Handhabung der Geräte am Ende Ihrer Lebensdauer ergeben
könnten.
Genauere Informationen zur nächstgelegenen Sammelstelle bzw. Recyclinghof
erhalten Sie bei Ihrer Gemeindeverwaltung.
Für Geschäftskunden in der Europäischen Union
Bitte treten Sie mit Ihrem Händler oder Lieferanten in Kontakt, wenn Sie elektrische und elektronische
Geräte entsorgen möchten. Er hält weitere Informationen für sie bereit.
Informationen zur Entsorgung in Ländern außerhalb der Europäischen Union
Dieses Symbol ist nur in der Europäischen Union gültig.
VQT3N28_E.book 14 ページ 2011年5月26日 木曜日 午前9時34分
15
VQT3N28
Objektivpflege
Sand und Staub können das Objektiv
beschädigen. Achten Sie darauf, dass kein
Sand oder Staub auf Objektiv oder Anschlüsse
gelangt, wenn Sie die Kamera im Freien, z.B.
am Strand, verwenden.
Dieses Objektiv ist nicht wasserdicht. Wenn
Regenwasser oder anderes Wasser auf das
Objektiv spritzt, wischen Sie es mit einem
trockenen Tuch ab.
Üben Sie keinen zu starken Druck auf das Objektiv aus.
Schmutz auf dem Objektiv (Wasser, Öl,
Fingerabdrücke usw.) kann zu schlechteren Bildern
führen. Wischen Sie die Objektivoberfläche vor und
nach dem Fotografieren vorsichtig mit einem
weichen, trockenen Tuch ab.
Richten Sie die Objektivfassung nicht nach unten.
Achten Sie darauf, dass der Kontaktpunkt der
Objektivfassung 1 nicht verschmutzen.
Hinweise zu Kondensation (Beschlagen
des Objektivs)
Kondensation entsteht, wenn sich
Umgebungstemperatur oder Luftfeuchte wie unten
beschrieben ändern. Da Kondensation zu Flecken
auf dem Objektiv, Pilzbefall und Fehlfunktionen
führen kann, müssen Sie in folgenden Fällen auf
Anzeichen von Kondensation achten:
Die Kamera wird bei kaltem Wetter von draußen
nach drinnen gebracht
Die Kamera wird in ein klimatisiertes Auto gebracht
Eine Klimaanlage bläst kalte Luft direkt auf das
Objektiv
Die Kamera wird bei hoher Luftfeuchte verwendet
Sie vermeiden Kondensation, wenn Sie die
Kamera in einer geschlossenen Plastiktüte
transportieren und diese erst dann öffnen, wenn
sich die Kamera an die Umgebungstemperatur
angepasst hat. Wenn sich Kondensation bildet,
schalten Sie die Kamera aus und lassen Sie sie
für etwa zwei Stunden ausgeschaltet. Die
Kondensation baut sich während der Anpassung
der Kamera an die Umgebung auf natürlichem
Wege ab.
Vermeidung von Störungen
VQT3N28_E.book 15 ページ 2011年6月14日 火曜日 午前11時49
16
VQT3N28
Beiliegendes Zubehör
[Kontrollen, die beim Entfernen der Verpackung
des Geräts vorzunehmen sind]
Prüfen Sie beim Entnehmen des Gerätes aus seinem
Karton, ob das Hauptgerät und sein beiliegendes Zubehör
vorhanden sind. Kontrollieren Sie deren äußeres
Aussehen und ihre Funktionsweise, um zu prüfen, dass
es während des Vertriebs und Transports nicht zu
Beschädigungen gekommen ist.
Setzen Sie sich, sollten Sie Störungen feststellen, vor dem
Gebrauch des Gerätes mit Ihrem Händler in Verbindung.
Die Produktnummern entsprechen dem Stand von
Juli 2011. Änderungen bleiben vorbehalten.
1 Objektivtasche
2 Gegenlichtblende
3 Objektivdeckel
4 Hinterer Objektivdeckel
(Beim Kauf sind der hintere Objektivdeckel und der
Objektivdeckel auf das Wechselobjektiv aufgesetzt.)
Objektiv ansetzen/abnehmen
Informationen zum Aufsetzen und Abnehmen des
Objektivs finden Sie auch in der
Bedienungsanleitung der Kamera.
Das Objektiv aufsetzen
Stellen Sie sicher, dass die Kamera ausgeschaltet ist.
1
Drehen Sie den hinteren
Objektivdeckel, um ihn
abzunehmen
.
A: Hinterer Objektivdeckel
2 Richten Sie die roten
Markierungen B zum
Ansetzen des Objektivs
auf Kameragehäuse und
Objektiv aneinander aus
und drehen Sie das
Objektiv in Pfeilrichtung,
bis es hörbar einrastet.
Drücken Sie nicht die Objektivfreigabetaste C
wenn Sie ein Objektiv anschließen.
Versuchen Sie niemals, das Objektiv schräg
zum Gehäuse anzusetzen, da die
Objektivfassung beschädigt werden könnte.
VFC4456 VYC1063 VYF3284
123
VFC4605
4
VQT3N28_E.book 16 ページ 2011年6月14日 火曜日 午前11時49
17
VQT3N28
• Überprüfen Sie, ob das Objektiv richtig aufgesetzt ist.
Das Objektiv abnehmen
Stellen Sie sicher, dass die Kamera ausgeschaltet ist.
Drehen Sie beim Betätigen der
Objektivfreigabetaste D das Objektiv in
Pfeilrichtung bis zum Anschlag und
entfernen Sie es.
Setzen Sie den hinteren
Objektivdeckel auf, um die
Kontakte der Objektivfassung
nicht zu beschädigen.
• Setzen Sie den Gehäusedeckel
der Kamera auf, damit kein
Schmutz oder Staub ins
Kamerainnere gelangen kann.
Objektivdeckel aufsetzen und abnehmen
Drücken Sie zum Anbringen oder
Abnehmen des Objektivdeckels wie in
der Abbildung gezeigt darauf.
Verlieren Sie den
Objektivdeckel nicht.
Gegenlichtblende aufsetzen
(Mitgeliefertes Zubehör)
Setzen Sie die Gegenlichtblende so in
das Objektiv ein, dass die kürzeren
Vorsprünge oben und unten sitzen, und
drehen Sie die Gegenlichtblende in
Pfeilrichtung bis zum Anschlag.
E: Ausrichten der Markierungen
Wenn Sie bei aufgesetzter Gegenlichtblende
Aufnahmen mit Blitz machen, kann der untere
Teil des Bildes dunkel erscheinen
(Vignettierungseffekt/Randabschattung).
Außerdem funktioniert unter Umständen die
Blitzsteuerung nicht, weil das Blitzlicht durch die
Gegenlichtblende verdeckt wird. Wir empfehlen,
bei Blitzaufnahmen die Gegenlichtblende
abzunehmen.
Nehmen Sie die Gegenlichtblende ab, wenn Sie
bei wenig Licht mit der AF-Hilfslampe arbeiten.
VQT3N28_E.book 17 ページ 2011年6月14日 火曜日 午前11時49
18
VQT3N28
Filter aufsetzen
Falls zwei oder mehr Aufsätze, also
MC-Schutzfilter (Sonderzubehör: DMW-LMC46),
PL-Filter (Sonderzubehör: DMW-LPL46) oder
ND-Filter (Sonderzubehör: DMW-LND46),
verwendet werden oder falls der verwendete
Objektivschutz bzw. Filter besonders dick ist, kann
ein Vignettierungseffekt auftreten.
Der Filter lässt sich eventuell nicht mehr
abnehmen, wenn er zu fest angezogen wird.
Gehen Sie daher vorsichtig vor.
Der Objektivdeckel kann auch aufgesetzt werden,
wenn der Filter bereits angebracht ist.
Auf dieses Objektiv lassen sich weder
Vorsatzlinsen noch Adapter aufsetzen. Die
Verwendung von Filtern ist möglich, das
Aufsetzen anderer Komponenten dagegen kann
zu einer Beschädigung des Objektivs führen.
Bezeichnungen und
Funktionen der einzelnen
Kamerateile
1 Linsenfläche
2 Schärfenring
Drehen Sie zum Scharfstellen am Schärfenring,
wenn Sie Aufnahmen mit der manuellen
Scharfeinstellung machen.
3 Kontaktpunkt
4 Markierung zum Ansetzen des Objektivs
4
21
3
VQT3N28_E.book 18 ページ 2011年6月14日 火曜日 午前11時49
19
VQT3N28
Hinweis
Bildveränderungen durch die Fokusfunktion sind
unter Umständen je nach den
Aufnahmebedingungen deutlicher, wenn AF
während der Videoaufnahme betätigt wird. Es
wird geraten, den Fokus durch Einstellen der
Kamera auf manuellen Fokus (MF), usw. zu
fixieren, wenn Sie die Bildveränderungen als
störend empfinden.
Vorsichtsmaßnahmen
Achten Sie darauf, das Objektiv nicht fallen zu
lassen und keinen starken Stößen auszusetzen.
Üben Sie keinesfalls zu starken Druck auf das
Objektiv aus.
Achten Sie auch darauf, dass die Tasche, in der
Sie das Objektiv aufbewahren, nicht herunterfällt,
denn das Objektiv könnte sonst schwer
beschädigt werden. Unter Umständen funktioniert
dann auch die Kamera nicht mehr und kann keine
Bilder mehr aufzeichnen.
Wenn in der Umgebung der Kamera Pestizide
oder andere flüchtige Substanzen verwendet
werden, müssen Sie dafür sorgen, dass diese
Stoffe nicht in Kontakt mit der
Obektivoberfläche kommen.
Falls solche Substanzen auf das Objektiv gelangen,
könnten sie zur Beschädigung des Objektivs oder
zum Abblättern der Farbe führen.
Tragen Sie das Gerät nicht, während es noch an
der Kamera angebracht ist.
Keinesfalls darf das Gerät unter den folgenden
Bedingungen benutzt oder aufbewahrt werden, da
dies zu Defekten oder Funktionsstörungen führen
kann.
VQT3N28_E.book 19 ページ 2011年5月26日 木曜日 午前9時34分
20
VQT3N28
Bei direktem Sonnenlicht oder im Sommer an der
Küste
An Orten mit hohen Temperaturen und hoher
Feuchtigkeit, bzw. wo starke Änderungen bei
Temperatur und Feuchtigkeit erfolgen
An Orten mit hoher Konzentration von Sand,
Staub oder Schmutz
Bei einem Brand
In der Nähe von Heizkörpern, Klimaanlagen oder
Luftbefeuchtern
Wo Wasser das Gerät benässen kann
Wo Erschütterungen vorhanden sind
In einem Fahrzeug
Weiter Informationen finden Sie auch in der
Bedienungsanleitung der Kamera.
Wenn für längere Zeit kein Einsatz erfolgt, lagern
Sie das Objektiv gemeinsam mit einem
Trocknungsmittel (Silica-Gel). Ohne ausreichende
Trocknung kann die Einsatzfähigkeit des
Objektivs durch Schimmel usw. beeinträchtigt
oder der Einsatz völlig unmöglich werden. Es wird
empfohlen, die Funktionsfähigkeit des Gerätes vor
dem Gebrauch zu prüfen.
Stellen Sie sicher, dass das Objektiv nicht über
einen längeren Zeitraum in Kontakt mit Gummi-
oder Plastikprodukten kommt.
Berühren Sie nicht die elektrischen Kontakte des
Gerätes. Dadurch kann es zu einem Defekt am
Gerät kommen.
Nehmen Sie das Gerät nicht auseinander und
nehmen Sie keine Veränderungen daran vor.
Verwenden Sie zur Reinigung der Geräte kein
Waschbenzin, Alkohol oder ähnliche
Reinigungsmittel.
Lösungsmittel können zur Beschädigung des
Objektivs oder zum Abblättern der Farbe führen.
Staub und Fingerabdrücke lassen sich mit einem
weichen, trockenen Tuch entfernen.
Verwenden Sie ein trockenes Staubtuch, um
Schmutz und Staub vom Schärfering zu entfernen.
Verwenden Sie keine Küchenspülmittel oder mit
Chemikalien getränkte Tücher.
Beim Ein- und Ausschalten ist ein Geräusch zu
hören.
Vom Objektiv wird beim Aufnehmen eines Bildes
von einem hellen Objekt, wie im Freien, ein
Geräusch erzeugt.
Dieses Geräusch wird durch die Blenden- oder
Objektivbewegung verursacht; es ist keine
Fehlfunktion.
Fehlerbehebung
VQT3N28_E.book 20 ページ 2011年6月14日 火曜日 午前11時49
1 / 1

Panasonic H-X025E Инструкция по применению

Категория
Объективы для камеры
Тип
Инструкция по применению
Это руководство также подходит для

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

Спросите документ