LG 43LW641H Руководство пользователя

Категория
ЖК-телевизоры
Тип
Руководство пользователя
Please read this manual carefully before operating your
set and retain it for future reference.
Safety and Reference
OWNER’S MANUAL
www.lg.com
LED TV*
* LG LED TV applies LCD screen with LED backlights.
2
ENGLISH
Safety instructions
Please read these safety precautions carefully
before using the product.
WARNING
Do not place the TV and/or remote control in the following
environments:
•  A location exposed to direct sunlight
•  An area with high humidity such as a bathroom
•  Near any heat source such as stoves and other devices that produce
heat
•  Near kitchen counters or humidiers where they can easily be
exposed to steam or oil
•  An area exposed to rain or wind
•  Near containers of water such as vases
Otherwise, this may result in re, electric shock, malfunction or product
deformation.
Do not place the product where it might be exposed to dust. This may
cause a re hazard.
Mains Plug is the TV connecting/disconnecting device to AC mains
electric supply. This plug must remain readily attached and operable
when TV is in use.
Do not touch the power plug with wet hands. Additionally, if the cord
pin is wet or covered with dust, dry the power plug completely or wipe
dust o. You may be electrocuted due to excess moisture.
Make sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.
Insert power cable plug completely into wall socket otherwise if not
secured completely into socket, re ignition may break out.
Ensure the power cord does not come into contact with hot objects such
as a heater. This may cause a re or an electric shock hazard.
Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in re or electric shock.
Bend antenna cable between inside and outside building to prevent
rain from owing in. This may cause water damaged inside the Product
and could give an electric shock.
When mounting TV onto wall make sure to neatly install and isolate
cabling from rear of TV as to not create possibility of electric shock /
re hazard.
Do not plug too many electrical devices into a single multiple electrical
outlet. Otherwise, this may result in re due to over-heating.
ENGLISH
3
Do not drop the product or let it fall over when connecting external
devices. Otherwise, this may result in injury or damage to the product.
Desiccant
Keep the anti-moisture packing material or vinyl packing out of the
reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suocation. Keep it out of
the reach of children.
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
Dispose of used batteries carefully to ensure that a small child does not
consume them. Please seek Doctor- Medical Attention immediately if
child consumes batteries.
Do not insert any metal objects/conductors (like a metal chopstick/
cutlery/screwdriver) between power cable plug and input Wall Socket
while it is connected to the input terminal on the wall. Additionally,
do not touch the power cable right after plugging into the wall input
terminal. You may be electrocuted. (Depending on model)
Do not put or store inammable substances near the product. There is a
danger of combustion/explosion or re due to careless handling of the
inammable substances.
Do not drop metallic objects such as coins, hair pins, chopsticks or wire
into the product, or inammable objects such as paper and matches.
Children must pay particular attention. Electrical shock, re or injury
can occur. If a foreign object is dropped into the product, unplug the
power cord and contact the service centre.
Do not spray water on the product or scrub with an inammable
substance (thinner or benzene). Fire or electric shock accident can occur.
Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there is leakage of gas, open the
windows and ventilate. It may cause a re or a burn by a spark.
Do not disassemble, repair or modify the product at your own
discretion. Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
4
ENGLISH
If any of the following occur, unplug the product immediately and
contact your local service centre.
•  The product has been impacted by shock
•  The product has been damaged
•  Foreign objects have entered the product
•  The product produced smoke or a strange smell
This may result in re or electric shock.
Unplug the TV from AC mains wall socket if you do not intend to use the
TV for a long period of time. Accumulated dust can cause re hazard
and insulation deterioration can cause electric leakage/shock/re.
Apparatus shall not be exposed to dripping or splashing and no objects
lled with liquids, such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could be exposed to oil or oil
mist. This may damage the product and cause it to fall.
If water enters or comes into contact with TV, AC adapter or power
cord please disconnect the power cord and contact service centre
immediately. Otherwise, this may result in electric shock or re.
Only use an authorized AC adapter and power cord approved by
LG Electronics. Otherwise, this may result in re, electric shock,
malfunction or product deformation.
Never Disassemble the AC adapter or power cord. This may result in re
or electric shock.
Be careful in handling the adapter to prevent any external shocks to it.
An external shock may cause damage to the adapter.
Make sure the power cord is connected securely to the power plug on
the TV. (Depending on model)
CAUTION
Install the product where no radio wave occurs.
There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when the
antenna falls. This may cause an electric shock.
Do not install the product on places such as unstable shelves or inclined
surfaces. Also avoid places where there is vibration or where the
product cannot be fully supported. Otherwise, the product may fall or
ip over, which may cause injury or damage to the product.
If you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which
may cause injury.
If you intend to mount the product to a wall, attach VESA standard
mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts), x
it carefully so as not to drop.
Only use the attachments / accessories specied by the manufacturer.
ENGLISH
5
When installing the antenna, consult with a qualied service
technician. If not installed by a qualied technician, this may create a
re hazard or an electric shock hazard.
We recommend that you maintain a distance of at least 2 to 7 times
the diagonal screen size when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
Only use the specied type of battery. This could cause damage to the
remote control.
Do not mix new batteries with old batteries. This may cause the
batteries to overheat and leak.
Batteries should not be exposed to excessive heat. For example, keep
away from direct Sunlight , open replace and electric heaters.
Do not place non-rechargeable batteries in charging device.
Make sure there are no objects between the remote control and its
sensor.
Signal from Remote Control can be interrupted due to external/internal
lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting
or darken viewing area.
When connecting external devices such as video game consoles, make
sure the connecting cables are long enough. Otherwise, the product
may fall over, which may cause injury or damage the product.
Do not turn the product On/O by plugging-in or unplugging the power
plug to the wall outlet. (Do not use the power plug for switch.) It may
cause mechanical failure or could give an electric shock.
Please follow the installation instructions below to prevent the product
from overheating.
•  The distance between the product and the wall should be more
than 10cm.
•  Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
•  Do not install the product on a carpet or cushion.
•  Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in re.
Take care not to touch the ventilation openings when watching the TV
for long periods as the ventilation openings may become hot. This does
not aect the operation or performance of the product.
Periodically examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an exact replacement part
by an Authorized Service agent.
Prevent dust collecting on the power plug pins or outlet. This may cause
a re hazard.
6
ENGLISH
Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the cord
exits the appliance.
Do not press strongly upon the panel with a hand or sharp object such
as nail, pencil or pen, or make a scratch on it, as it may causedamage
to screen.
Avoid touching the screen or holding your nger(s) against it for long
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
When cleaning the product and its components, unplug the power
rst and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with water or wipe with a wet
cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,
benzene, alcohol etc., which can damage the product and its panel.
Otherwise, this may result in re, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall outlet, it is not
disconnected from the AC power source even if you turn o this unit
by SWITCH.
When unplugging the cable, grab the plug and unplug it, by pulling at
the plug.
Don’t pull at the cord to unplug the power cord from the power board,
as this could be hazardous.
When moving the product, make sure you turn the power o rst. Then,
unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a re
hazard or cause electric shock.
When moving or unpacking the product, work in pairs because the
product is heavy. Otherwise, this may result in injury.
Refer all servicing to qualied service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
If the product feels cold to the touch, there may be a small “icker”
when it is turned on. This is normal, there is nothing wrong with
product.
This panel is an advanced product that contains millions of pixels.
You may see tiny black dots and/or brightly coloured dots (red, blue
or green) at a size of 1ppm on the panel. This does not indicate a
malfunction and does not aect the performance and reliability of the
product.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
ENGLISH
7
You may nd dierent brightness and color of the panel depending on
your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
Displaying a still image for a prolonged period of time may cause image
sticking. Avoid displaying a xed image on the TV screen for a long
period of time.
Generated Sound
“Cracking noise: A cracking noise that occurs when watching or turning
o the TV is generated by plastic thermal contraction due to tempera-
ture and humidity. This noise is common for products where thermal
deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit,
which supplies a large amount of current to operate a product. It varies
depending on the product.
This generated sound does not aect the performance and reliability
of the product.
Do not use high voltage electrical goods near the TV (e.g. electric
mosquito-swatter). This may result in product malfunction.
Viewing 3D imaging (Only 3D
models)
CAUTION
•  Children should be supervised by an adult when viewing 3D video.
If a child experiences eye fatigue, headaches or blurred vision
while watching 3D, they should take a break, before they resume
watching 3D content.
•  When viewing a 3D video, some may experience discomfort such as
a headache, dizziness, fatigue, or blurred vision. In this case, stop
watching the 3D video and take a rest.
•  If you watch a 3D video for a long time, you may experience eye
fatigue. In this case, stop watching the 3D video and take a rest.
•  Only use LG 3D glasses. Otherwise, you may not be able to view 3D
videos properly.
•  Do not use 3D glasses instead of your normal glasses, sunglasses,
or protective goggles.
•  Do not keep your 3D glasses in extremely high or low
temperatures. It will cause deformation.
•  Do not use 3D glasses while walking or moving around. It may
cause an accident or injury.
•  Be careful not to poke your eye with the frames of the 3D glasses.
•  Do not watch 3D content if you have photosensitive seizures,
epilepsy, or heart disease.
8
ENGLISH
Preparing
NOTE
•  If the TV is turned on for the rst time after it was shipped from the
factory, initialization of the TV may take a few minutes.
•  Image shown may dier from your TV.
•  Your TV’s OSD (On Screen Display) may dier slightly from that
shown in this manual.
•  The available menus and options may dier from the input source
or product model that you are using.
•  New features may be added to this TV in the future.
•  The items supplied with your product may vary depending on the
model.
•  Product specications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
•  For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not t into your TV’s USB port.
A
B
A
B
*A
<
=
10 mm
*B
<
=
18 mm
•  Use a certied cable with the HDMI logo attached.
•  If you do not use a certied HDMI cable, the screen may not display
or a connection error may occur. (Recommended HDMI Cable Types)
- High-Speed HDMI
®
/
TM
cable (3 m or less)
- High-Speed HDMI
®
/
TM
cable with Ethernet (3 m or less)
CAUTION
•  Do not use any unapproved items to ensure the safety and product
life span.
•  Any damage or injuries caused by using unapproved items are not
covered by the warranty.
•  Some models have a thin lm attached on to the screen and this
must not be removed.
•  When attaching the stand to the TV set, place the screen facing
down on a cushioned table or at surface to protect the screen
from scratches.
•  Make sure that the screws are inserted correctly and fastened
securely. (If they are not fastened securely enough, the TV may tilt
forward after being installed.) Do not use too much force and over
tighten the screws; otherwise screw may be damaged and not
tighten correctly.
•  Make sure to wring any excess water or cleaner from the cloth.
•  Do not spray water or cleaner directly onto the TV screen.
•  Make sure to spray just enough of water or cleaner onto a dry cloth
to wipe the screen.
•  When cleaning the product, be careful not to allow any liquid or
foreign objects to enter the gap between the upper, left or right
side of the panel and the guide panel. (Depending on model)
Separate purchase
Separate purchase items can be changed or modied for quality
improvement without any notication. Contact your dealer to buy
these items. These devices only work with certain models. The model
name or design may be changed depending on the upgrade of product
functions, manufacturer’s circumstances or policies.
(Depending on model)
LEC-003
LED Clock
LEC-004
LED Clock
AG-F***
Cinema 3D Glasses
AN-MR650
Magic Remote
ENGLISH
9
Lifting and moving the TV
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
•  It is recommended to move the TV in the box or packing material
that the TV originally came in.
•  Before moving or lifting the TV, disconnect the power cord and
all cables.
•  When holding the TV, the screen should face away from you to
avoid damage.
•  Hold the top and bottom of the TV frame rmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
•  When transporting a large TV, there should be at least 2 people.
•  When transporting the TV by hand, hold the TV as shown in the
following illustration.
•  When transporting the TV, do not expose the TV to jolts or
excessive vibration.
•  When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right.
•  Do not apply excessive pressure to cause exing / bending of frame
chassis as it may damage screen.
•  When handling the TV, be careful not to damage the protruding
buttons.
CAUTION
•  Avoid touching the screen at all times, as this may result in damage
to the screen.
•  Do not move the TV by holding the cable holders, as the cable
holders may break, and injuries and damage to the TV may occur.
Using the button
(Depending on model)
You can simply operate the TV functions, pressing or moving the button.
Joystick Button
Dome Button
or
Basic functions
Power On (Press)
Power O (Press and hold)
1
Volume Control
Programmes Control
1 All running apps will close, and any recording in progress will stop.
Adjusting the menu
When the TV is turned on, press the button one time. You can adjust
the Menu items pressing or moving the buttons.
Turns the power o.
Clears on-screen displays and returns to TV viewing.
Changes the input source.
Accesses the settings menu.
10
ENGLISH
Mounting on a table
1 Lift and tilt the TV into its upright position on a table.
•  Leave a 10 cm (minimum) space from the wall for proper
ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
•  Do not place the TV near or on sources of heat, as this may result in
re or other damage.
Attaching the TV to a desk
(This feature is not available for all models.)
The TV should be attached to a desk so it cannot be pulled in a forward/
backward direction, potentially causing injury or damaging the product.
4-Screws
(Not supplied with TV)
A type)
Desk
Stand
NOTE
•  Screw : M5 x L (*L: Table depth + 8~10 mm)
ex) Table depth: 15 mm, Screw : M5 x L25
2-Screws for Stand Fixing,
2-Washers for Stand Fixing,
2-Nuts for Stand Fixing
(Supplied with TV)
B type)
Desk
Stand
Using the kensington security
system
(This feature is not available for all models.)
The Kensington security system connector is located at the rear of the
TV. For more information of installation and using, refer to the manual
provided with the Kensington security system or visit http://www.
kensington.com. Connect the Kensington security system cable between
the TV and a table.
ENGLISH
11
Securing the TV to a wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
•  If there are bolts inserted at the eye-bolts position, remove the
bolts rst.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the at surface.
CAUTION
•  Make sure that children do not climb on or hang on the TV.
NOTE
•  Use a platform or cabinet that is strong and large enough to
support the TV securely.
•  Brackets, bolts and ropes are not provided. You can obtain
additional accessories from your local dealer.
Adjusting the angle of the TV to suit
view
(This feature is not available for all models.)
Swivel 20 degrees to the left or right and adjust the angle of the TV to
suit your view.
20˚20˚
CAUTION
•  When adjusting the angle of the product, watch out for your
ngers.
- Personal injury may occur if hands or ngers are pinched. If the
product is tilted too much, it may fall, causing damage or injury.
Mounting on a wall
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the oor. When you attach the TV to other building materials, please
contact qualied personnel. LG recommends that wall mounting be
performed by a qualied professional installer. We recommend the use
of LG’s wall mount bracket. LGs wall mount bracket is easy to move with
cables connected. When you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is adequately secured to the
wall with enough space to allow connectivity to external devices. It is
advised to connect all the cables before installing xed wall mounts.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
Separate purchase(Wall Mounting Bracket)
Model
43UW76**
32/43LW64**
43UW95**
49/55UW76**
49/55UW96**
VESA (A x B) (mm) 200 x 200 300 x 300
Standard screw M6 M6
Number of screws 4 4
Wall mount
bracket
LSW240B
MSW240
LSW350B
MSW240
Model 65UW96** 75UW34**
VESA (A x B) (mm) 300 x 300 600 x 400
Standard screw M6 M6
Number of screws 4 4
Wall mount
bracket
LSW350B LSW640B
A
B
12
ENGLISH
CAUTION
•  Remove the stand before installing the TV on a wall mount by
performing the stand attachment in reverse.
NOTE
•  When installing the wall mounting bracket, use the adhesive label
or protective cover provided. The adhesive label or protective cover
will protect the opening from accumulating dust and dirt. (Only
when the label or cover is provided)
Provided item
Adhesive label
Provided item
Adhesive label
Provided item
Protective cover
•  When installing the wall mounting bracket, it is recommended to
cover the stand hole using tape, in order to prevent the inux of
dust and insects. (Depending on model)
Stand hole
Connections (notications)
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external devices
connection, refer to the manual provided with each device.
Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
devices.
NOTE
•  The external device connection may dier from the model.
•  Connect external devices to the TV regardless of the order of the
TV port.
•  If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
•  Refer to the external equipment’s manual for operating
instructions.
•  If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
•  In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change
the PC output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the PICTURE
menu until the picture is clear.
•  In PC mode, some resolution settings may not work properly
depending on the graphics card.
•  If ULTRA HD content is played on your PC, video or audio may
become disrupted intermittently depending on your PC’s
performance. (Depending on model)
ENGLISH
13
Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
•  Use a signal splitter to use more than 2 TVs.
•  If the image quality is poor, install a signal amplier properly to
improve the image quality.
•  If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
•  An antenna cable and converter are not supplied.
•  Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC
•  For a location that is not supported with ULTRA HD broadcasting,
this TV cannot receive ULTRA HD broadcasts directly. (Depending
on model)
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω).
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV mode.
•  Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can
cause damage to the TV and the PCMCIA card slot.
•  If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service
Operator.
USB connection
Some USB Hubs may not work. If a USB device connected through a USB
Hub is not detected,connect it directly to the USB port on the TV.
Speaker Output Setup
(Depending on model)
STEREO
(8Ω)
VOLUME
CONTROL
+
-
UP
DOWN
GND
RIGHT
LEFT
GND
Control port for Speaker out
NOTE
•  Use only with the 3 Pole 3.5 mm Stereo Jack.
•  Do not connect your headphones or earphones to the port for
connecting an external speaker.
Method of Volume control port
•  Cable Spec.
VOLUME CONTROL
+
-
GND / UP / DOWN
Each Up / Down pin
is pulled to 3.3V with
CPU GPIO.
CPU detects transition
from 3.3V to GND level
for volume control.
14
ENGLISH
Network Setup
Wired network connection
(Depending on model)
This TV can be connected to a Pro:Centric server via the LAN port. After
making the physical connection, the TV needs to be set up for network
communication.
Connect the LAN port of the Modem or Router from Pro:Centric server
to the LAN port on the TV.
Broadband Modem
2 1
Pro:Centric Server
Broadband Modem
Pro:Centric Server
Router
Broadband Modem
1
Connect the LAN port of the Modem or Router to the LAN port
on the TV.
2
Connect the LAN port of the PC to the AUX LAN port on the TV.
(Depending on model)
CAUTION
•  Do not connect a modular phone cable to the LAN port.
•  Since there are various connection methods, please follow the
specications of your telecommunication carrier or internet service
provider.
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
• 
General HDMI ULTRA HD Deep
Colour
- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0)
- Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)
If the device connected to Input Port also supports ULTRA HD Deep
Colour, your picture may be clearer. However, if the device doesn’t
support it, it may not work properly. In that case, connect the device
to a dierent HDMI port or change the TV’s HDMI ULTRA HD Deep
Colour setting to Off.
(This feature is available on certain models which are supported
ULTRA HD Deep Colour only.)
Remote control
(Depending on model)
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5
V AAA) matching the
and ends to the label inside the
compartment, and close the battery cover. To remove the batteries,
perform the installation actions in reverse.
Make sure to point the remote control toward the remote control sensor
on the TV.
ENGLISH
15
A
B
A
(POWER) Turns the TV on or o.
Adjusts the brightness of the screen to reduce
energy consumption.
By zooming in on the selected area, you can view it
in full screen.
Changes the input source.
Selects Radio, TV and DTV programme.
Number buttons Enters numbers.
Accesses the saved programme list.
(Space) Opens an empty space on the screen keyboard.
Returns to the previously viewed programme.
B
Adjusts the volume level.
Accesses the Home menu.
Shows the previous history.
Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen.
C
D
C
Shows programme guide.
Displays and removes hotel interactive menu.
Views the information of the current programme and
screen.
Navigation buttons (up/down/left/right) Scrolls through menus
or options.
Selects menus or options and conrms your input.
Accesses the Quick Settings.
(BACK) Returns to the previous level.
Clears on-screen displays and return to TV viewing.
D
These access special functions in some menus.
(
: Red, : Green, : Yellow, : Blue)
Teletext buttons (
/ ) These buttons are used for
teletext.
Recalls your preferred subtitle in digital mode.
Control buttons (
) Controls media contents.
Used for viewing 3D video. (depending on model)
/ Selects the MHP TV menu source. (depending on model)
/ By pressing the AD button, audio descriptions function will be
enabled. (depending on model)
/ Sets the alarm function. (depending on model)
16
ENGLISH
Licenses
Supported licenses may dier by model. For more information about
licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
The terms HDMI and HDMI High-Denition Multimedia interface,
and the HDMI logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
For DTS patents, see http://patents.dts.com. Manufactured under
license from DTS Licensing Limited. DTS, DTS-HD, the Symbol, & DTS
or DTS-HD and the Symbol together are registered trademarks of
DTS, Inc. © DTS, Inc. All Rights Reserved.
Open source software
notice information
To obtain the source code under GPL, LGPL, MPL and other open source
licenses, that is contained in this product, please visit http://opensource.
lge.com.
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
[email protected]om. This oer is valid for three (3) years from the date
on which you purchased the product.
Troubleshooting
The software version can be updated for improvement in performance.
Customer needs to ensure the compatibility of customer’s equipment
with LGE software. If needed, please consult with LGE and upload
revised software version according to the guidance provided by LGE.
Cannot control the TV with the remote control.
•  Check the remote control sensor on the product and try again.
•  Check if there is any obstacle between the product and the remote
control.
•  Check if the batteries are still working and properly installed (
to , to ).
No image display and no sound is produced.
•  Check if the product is turned on.
•  Check if the power cord is connected to a wall outlet.
•  Check if there is a problem in the wall outlet by connecting other
products.
The TV turns o suddenly.
•  Check the power control settings. The power supply may be
interrupted.
•  Check if the Auto Power O (Depending on model) / Sleep
Timer / Timer Power O is activated in the Timers settings.
•  If there is no signal while the TV is on, the TV will turn o
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI), ‘No signal’ or ‘Invalid Format’ is
displayed.
•  Turn the TV o/on using the remote control.
•  Reconnect the HDMI cable.
•  Restart the PC with the TV on.
ENGLISH
17
Specications
Wireless module specification
•  As band channels can vary per country, the user cannot change or
adjust the operating frequency. This product is congured for the
regional frequency table.
•  For consideration of the user, this device should be installed and
operated with a minimum distance of 20 cm between the device
and the body.
(Only UW761*, UW961*, UW950*, UW341*)
Wireless module (LGSBWAC61) specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency Range Output Power (Max.)
2400 to 2483.5 MHz
5150 to 5725 MHz
5725 to 5850 MHz (Not for EU)
15.5 dBm
17.5 dBm
8.0 dBm
Bluetooth
Frequency Range Output Power (Max.)
2400 to 2483.5 MHz 10 dBm
* “IEEE802.11ac is not available in all countries.
(Only LW641*)
Wireless module (LGSBW41) specifications
Wireless LAN (IEEE 802.11a/b/g/n)
Frequency Range Output Power (Max.)
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz (Not for EU)
16 dBm
16 dBm
11.5 dBm
Bluetooth
Frequency Range Output Power (Max.)
2400 to 2483.5 MHz 10 dBm
18
ENGLISH
CI Module (W x H x D) 100.0 mm x 55.0 mm x 5.0 mm
Environment
condition
Operating Temperature 0 °C to 40 °C
Operating Humidity Less than 80 %
Storage Temperature -20 °C to 60 °C
Storage Humidity Less than 85 %
(Depending on country)
Digital TV Analogue TV
Satellite Terrestrial Cable Terrestrial / Cable
Television system
DVB-S/S2*
DVB-T
DVB-T2*
DVB-C
PAL/SECAM B/G, D/K, I,
SECAM L
Channel coverage
(Band)
950 ~ 2150 Mhz
VHF
: 174 ~ 230 Mhz
UHF
: 470 ~ 606 Mhz
UHF
: 606 ~ 862 Mhz
S Band
: 230 ~ 300 Mhz
S Band
: 300 ~ 470 Mhz
46 ~ 862 Mhz 46 ~ 862 Mhz
Maximum number of
storable programmes
6,000 3,000
External antenna
impedance
75 Ω
*Only DVB-T2/C/S2 support models.
ENGLISH
19
HDMI-DTV supported mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720 x 480
31.47
31.50
59.94
60.00
720 x 576 31.25 50.00
1280 x 720
44.96
45.00
37.50
59.94
60.00
50.00
1920 x 1080
28.12
33.72
33.75
26.97
27.00
33.71
33.75
56.25
67.43
67.50
50.00
59.94
60.00
23.97
24.00
29.97
30.00
50.00
59.94
60.00
3840 x 2160
53.95
54.00
56.25
61.43
67.50
112.50
135.00
135.00
23.98
24.00
25.00
29.97
30.00
50.00
59.94
60.00
4096 x 2160
53.95
54.00
56.25
61.43
67.50
112.50
135.00
135.00
23.98
24.00
25.00
29.97
30.00
50.00
59.94
60.00
1
: Only UW761*, UW961*, UW950*, UW341*
RGB-PC supported mode
(Only UW341*)
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
640 x 350 31.468 70.09
720 x 400 31.469 70.08
640 x 480 31.469 59.94
800 x 600 37.879 60.31
1024 x 768 48.363 60.00
1152 x 864 54.348 60.053
1280 x 1024 63.981 60.020
1360 x 768 47.712 60.015
1920 x 1080
66.587 59.934
67.50 60.00
HDMI-PC supported Mode
•  PC audio is not supported
•  Use HDMI IN 1 for PC mode (Depending on model)
Resolution
Horizontal
Frequency (kHz)
Vertical Frequency
(Hz)
640 x 350 31.46 70.09
720 x 400 31.46 70.08
640 x 480 31.46 59.94
800 x 600 37.87 60.31
1024 x 768 48.36 60.00
1152 x 864 54.34 60.05
1280 x 1024 63.98 60.02
1360 x 768 47.71 60.01
1920 x 1080 67.50 60.00
3840 x 2160
67.50
56.25
54.00
30.00
25.00
24.00
4096 x 2160
53.95
54.00
23.97
24.00
1
: Only UW761*, UW961*, UW950*, UW341*
NOTE
•  The optimal display resolution
- 3840 X 2160 (Only UW761*, UW961*, UW950*, UW341*)
- 1920 x 1080 (Only LW641* )
Component port connecting
information
Component ports on the TV Y P
B
P
R
Video output ports on
DVD player
Y P
B
P
R
Y B-Y R-Y
Y Cb Cr
Y Pb Pr
Signal Component
480i / 576i O
480p / 576p O
720p / 1080i O
1080p
O
(Only 50 Hz / 60 Hz)
1
1
20
ENGLISH
3D supported mode (Only 3D models)
•  Video, which is input as below media contents is switched into the 3D screen automatically. The method for 3D digital broadcast may dier
depending on the signal environment. If video is not switched automatically into 3D, manually convert the settings to view 3D images. For
models supporting Miracast / Intel® WiDi, you can set the 3D mode.
3D supported mode automatically
Input Signal
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Playable 3D video format
RF
1280 x 720 37.500 50
2D to 3D, Side by Side, Top & Bottom
1920 x 1080 28.125 50
HDMI
640 x 480
31.47 / 31.50
59.94 / 60.00
Top & Bottom, Side by Side(Half),
Side by Side (Full)
62.94 / 63.00 Frame Packing, Line Alternative
720 x 480
31.47 / 31.50
59.94 / 60.00
Top & Bottom, Side by Side (Half), Side by Side (Full)
62.94 /63.00 Frame Packing, Line Alternative
720 x 576
15.63
50.00
Top & Bottom, Side by Side (Half),
Side by Side (Full), Frame Packing
31.25 Top & Bottom, Side by Side (Half), Side by Side (Full)
62.50 Frame Packing, Line Alternative
1280 x 720
37.50 50.00
Top & Bottom, Side by Side (Half), Side by Side (Full)
44.96 / 45.00 59.94 / 60.00
75.00 50.00
Frame Packing, Line Alternative
89.91/90.00 59.94 / 60.00
1920 x 1080
28.13 50.00
Top & Bottom, Side by Side (Half), Side by Side (Full)
33.72 / 33.75 59.94 / 60.00
56.25 50.00
Frame Packing
67.43/67.50 59.94 / 60.00
26.97 / 27.00 23.97 / 24.00
Top & Bottom, Side by Side (Half), Side by Side (Full)28.12 25.00
33.72 / 33.75 29.98 / 30.00
43.94 / 54.00 23.97 / 24.00
Frame Packing, Line Alternative56.25 25.00
67.43 / 67.5 29.98 / 30.00
56.25 50.00
Top & Bottom, Side by Side (Half)
67.43 / 67.50 59.94 / 60.00
USB
1080p 33.75 30.00
Side by Side (Half), Top & Bottom, Side by Side (Full), Frame
Sequential, MPO (Photo), JPS (Photo)
2160p 67.50 30.00
1 / 1

LG 43LW641H Руководство пользователя

Категория
ЖК-телевизоры
Тип
Руководство пользователя

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

Спросите документ